Reptilia's CQG grip has been specifically designed to enhance ergonomics and performance of compact sized short-barreled rifles AR15 pistols pistol caliber carbines and PDWs.

The CQG supports a wide range of hand sizes and weapon configurations featuring a more pronounced vertical grip angle anti-slip front and rear texture and an enhanced beaver tail design; the CQG encourages the shooter’s hand to be positioned higher on the grip for greater control and improved comfort.

Fits AR15/AR10/SR25/MCX/FN SCAR 16 and 17 Pattern Hosts
Toughened and Reinforced Nylon
77 grams
MADE IN USA

Introducing the ultra Low Height DOT Mount for Aimpoint ACRO and Steiner Optics MPS by Reptilia. This mount is a lightweight, slim-line mounting solution for allowing for co-witness with BUIS on subguns and AKs with gas tube with 1913 Picatinny atop. Machined from billet 7075-T6 aluminum with Milspec Type III hard anodized finish, this Low DOT Mount attaches to any M1913 Picatinny rail. Its spring-loaded nitrided steel clamp and mounting bolt simplify the installation process, and sit flush with the body of the mount for a low-profile, anti-snag design.

Reptilia’s DOT Mount is billet-machined from 7075-T6 aluminum and pairs a spring-loaded steel clamp with Picatinny rail compatibility. Its low-profile design sits flush without snags, and like all Reptilia products, it backs up with a lifetime warranty.

Specs

Fits: Aimpoint Micro, Micro R-1, H-1, H-2, T-1, T-2, CompM5, Sig ROMEO4/5
Height: 39mm (Lower 1/3 co-witness)
Material: Billet 7075-T6 aluminum
Finish: Milspec Type III hard anodized
Mount: Picatinny 1913 rails
Features: Spring-loaded nitrided steel clamp, low-profile anti-snag design
Warranty: Lifetime
Made in USA: Yes

Questions about fitment or availability? Give the shop a call and we’ll walk you through it.

The 1.93 inch height DOT Mount for HOLOSUN AEMS by Reptilia is a lightweight slim-line mounting solution for a variety of red dot optics. Machined from billet 7075-T6 aluminum with Milspec Type III hard anodized finish the 1.93 DOT Mount attaches to any M1913 Picatinny rail to place the optical axis at 1.93 inches above the rail. Its spring-loaded nitrided steel clamp and mounting bolt simplify the installation process and sit flush with the body of the mount for a low-profile anti-snag design.

Like all Reptilia products the DOT Mount is 100% made in the USA and carries a full lifetime warranty against manufacturer defects.

Compatible with: Holosun – AEMS

Features:

Type III hardcoat anodized 7075 aluminum
Nitrided 4140 steel Hardware
60 grams
Made in USA

Reptilia’s slim-line 1.93-inch mount raises your Aimpoint Micro or CompM5 to cowitness with AR-15 buis and modern tactical scopes. Machined from 7075-T6 aluminum with Milspec Type III hard anodizing, the spring-loaded nitrile steel clamp mounts securely to any M1913 rail with zero installation hassles.

Specs

Height: 1.93″ above rail
Fits: Aimpoint Micro, Micro H-1, H-2, T-1, T-2, CompM5
Mount Type: Picatinny rail
Material: 7075-T6 aluminum
Finish: Milspec Type III hard anodized
Weight: 1.9 oz

Questions about fitment or availability? Give the shop a call and we’ll walk you through it.

After more than two years of development and testing Reptilia is proud to announce the RECC·E Stock for AR15/M4. Designed at the request of a military end user the RECC·E Stock features a constant cheek weld ambidextrous QD sling attachment points rubber buttpad and a modular design that allows usage of a standard AR15 carbine buffer system or A5/SR25 carbine buffer system by replacing the receiver extension (buffer tube) and forward portion of the stock. Weighing only 12.0 ounces including the proprietary AR15 carbine-length receiver extension the RECC·E stock is the ideal lightweight solution for the entire spectrum of AR-pattern guns from compact to precision.

Receiver Extension: 7075-T6 Aluminum Type III Milspec Anodized Finish
Materials: Impact Modified Glass-Filled Nylon Polymer 7075 Type III anodized aluminum Nitrided alloy steel hardware
Weight: 12.0 oz.
Length of Pull: 10.8 in. – 14.2 in.
Patents Pending
MADE IN USA

Includes Reptilia's proprietary carbine length receiver extension “buffer tube” and all mounting hardware.

The RMU Mount by Reptilia is a lightweight slim-line solution manufactured at the request of a DoD customer. The RMU Mounts are ideal for lifting a variety of optics with fixed height lower 1/3 co-witness heights such as the EOTech line of holographic optics Vortex Optics AMG UH-1 and Sig Optics ROMEO8T to an elevated height which is more ergonomic when using helmet-borne night vision or those who prefer a more upright shooting stance.

The RMU Mount is machined from billet 7075-T6 aluminum with Milspec Type III hard anodized finish the RMU Mount attaches to any M1913 Picatinny rail and offers optimal sight placement with an increase in height of .625 inches. Its spring-loaded nitrided steel clamp and mounting bolt simplify the installation process and sit flush with the body of the mount for a low-profile anti-snag design.

Available in 12 9 and 6 slot configurations in a black anodized finish today!

Machined from billet 7075-T6 aluminum
Milspec Type III hard anodized finish
109 grams
Made in USA

ROF-90 ONLY COMPATIBLE WITH REPTILIA AUS MOUNTS AND GEISSELE SUPER PRECISION MOUNTS !

The ROF-90 is a drop-in upgrade for the Reptilia AUS Mount or Geissele Super Precision 30mm magnified optic mounts. Originally developed at the request of a user group for a quick transition to a non-magnified optic the ROF-90 was adds options for close-in target engagement and passive aiming with night vision. The ROF-90 for a Aimpoint ACRO or Steiner MPS at 90º (12:00) to add a close-range optic to your magnified scope. Additionally the ACRO or MPS can be zeroed for use with use with subsonic cartridges such as 300 AAC Blackout while allocating the magnified optic for use with supersonic ammunition.

Each ROF model is designed to minimize each optic’s distance from the host scope’s centerline while ensuring enough clearance that the sight picture isn’t obscured.

The 30mm ROF-90 for ACRO/MPS is immediately available in MIL-STD Type III Class 2 hard anodize Black and Flat Dark Earth and Clear colors.

Compatible with:

Aimpoint – ACRO P1 and P2
Steiner Optics – MPS

Features:

Machined from billet 7075-T6 aluminum
MIL-STD Type III hardcoat anodized
30 grams
Made in USA

ROF-90 ONLY COMPATIBLE WITH REPTILIA AUS MOUNTS AND GEISSELE SUPER PRECISION MOUNTS !

Introducing the Reptilia ROF-90 for ACRO / MPS in 34mm. The ROF-90 is a drop-in upgrade for the Reptilia AUS Mount or Geissele Super Precision 34mm magnified optic mounts. Originally developed at the request of a user group for a quick transition to a non-magnified optic the ROF-90 was adds options for close-in target engagement and passive aiming with night vision. The ROF-90 for a Aimpoint ACRO or Steiner MPS at 90º (12:00) to add a close-range optic to your magnified scope. Additionally the ACRO or MPS can be zeroed for use with use with subsonic cartridges such as 300 AAC Blackout while allocating the magnified optic for use with supersonic ammunition.

Each ROF model is designed to minimize each optic’s distance from the host scope’s centerline while ensuring enough clearance that the sight picture isn’t obscured.

The 34mm ROF-90 for ACRO/MPS is immediately available in MIL-STD Type III Class 2 hard anodize Black and Flat Dark Earth and Clear colors.

Compatible with:

Aimpoint – ACRO P1 and P2
Steiner Optics – MPS

Features:

Machined from billet 7075-T6 aluminum
MIL-STD Type III hardcoat anodized
35 grams
Made in USA

ROF-90 ONLY COMPATIBLE WITH REPTILIA AUS MOUNTS AND GEISSELE SUPER PRECISION MOUNTS !

Each ROF model is designed to minimize each optic’s distance from the host scope’s centerline while ensuring enough clearance that the sight picture isn’t obscured.

The 34mm ROF-90 for ACRO/MPS is immediately available in MIL-STD Type III Class 2 hard anodize Black and Flat Dark Earth and Clear colors.

Compatible with:

Aimpoint – ACRO P1 and P2
Steiner Optics – MPS

Features:

Machined from billet 7075-T6 aluminum
MIL-STD Type III hardcoat anodized
35 grams
Made in USA

ROF-90 ONLY COMPATIBLE WITH REPTILIA AUS MOUNTS AND GEISSELE SUPER PRECISION MOUNTS !

The 34mm ROF-90 is a drop-in upgrade for the Reptilia AUS Mount or Geissele Super Precision. The ROF-90 adds a mounting point at 90º (12:00) for a Trijicon RMR to provide for quick transition to a non-magnified optic for close-range target engagement. Additionally the RMR can be zeroed for use with use with subsonic cartridges such as 300 AAC Blackout while allocating the magnified optic for use with supersonic ammunition.

Each ROF model is designed to minimize each optic’s distance from the host scope’s centerline while ensuring enough clearance that the sight picture isn’t obscured.

The 34mm ROF-90 for RMR is immediately available in MIL-STD Type III Class 2 hard anodize black and flat dark earth colors.

Compatible with:

Trijicon – RMR & SRO
Holosun Technologies – HS407 HE407 HS507 HE507 & HE508 Series

Features:

For use with Reptilia AUS Mount or Geissele Super Precision Mount
Machined from billet 7075-T6 aluminum
MIL-STD Type III hardcoat anodized
33 grams
Made in USA

ROF-90 ONLY COMPATIBLE WITH REPTILIA AUS MOUNTS AND GEISSELE SUPER PRECISION MOUNTS !

Each ROF model is designed to minimize each optic’s distance from the host scope’s centerline while ensuring enough clearance that the sight picture isn’t obscured.

The 34mm ROF-90 for RMR is immediately available in MIL-STD Type III Class 2 hard anodize black and flat dark earth colors.

Compatible with:

Trijicon – RMR & SRO
Holosun Technologies – HS407 HE407 HS507 HE507 & HE508 Series

Features:

For use with Reptilia AUS Mount or Geissele Super Precision Mount
Machined from billet 7075-T6 aluminum
MIL-STD Type III hardcoat anodized
33 grams
Made in USA

Reptilia has the Saddle Mount for Steiner MPS & Aimpoint ACRO Optics for the Beretta 1301 & A300 line of shotguns. Machined from billet 7075-T6 Aluminum and finished with Milspec Type III Hard Coat Anodize the Saddle is the lowest possible mounting solution for miniature red dot optics utilizing the Aimpoint ACRO footprint allowing the user to co-witness the factory Beretta iron sights.

This mount utilizes the screws that come with the 1301 and A300.

Compatible with:

Aimpoint – ACRO
Steiner Optics – MPS

Features:

Machined from billet 7075-T6 aluminum
MIL-STD Type III hardcoat anodized
23 grams
Made in USA
Uses the screws that come with the 1301 and A300.

The Socket Mount M-LOK QD attachment point from Reptilia is driven by the request of an end user group for an anti-snag low profile streamline M-LOK attachment.

The Socket mount is machined from a single piece of billet 7075-T6 aluminum and is finished with MIL-STD Type III Class 2 hard anodize coating.

Like all Reptilia products the M-LOK QD Sling Mount is 100% made in the USA and carries a full lifetime warranty against manufacturer defects.

Machined from billet 7075-T6 aluminum
MIL-STD Type III hardcoat anodized
Magpul M-LOK Hardware
12 grams
Made in USA

Machined from aircraft grade billet aluminum with Milspec Type III Hardcoat Anodized finish the TORCH is optimized for use with the ATPIAL/PEQ 15 NGAL and other top-mounted aiming laser devices. Featuring an integral uni-body M-LOK interface it is not only low profile but provides the most robust M-LOK weapon light mounting solution on the market today. Available immediately in both left and right hand variants the TORCH 3V/CR123 is compatible with SureFire M300 Scout bezels and tail caps.

The TORCH 3V is immediately available in MIL-STD Type III Class 2 hard anodize black and contract over-run Tobacco.

Please note this is a light body only not a complete light.

Machined from billet 6061-T6 aluminum
MIL-STD Type III hardcoat anodized
Magpul M-LOK Hardware
28 grams
Made in USA