Dropping this kit into your Smith & Wesson M&P will set the trigger break point farther forward than the factory trigger assembly, as well as significantly reduce the uptake and over travel. It produces a trigger pull very similar to that of a 1911 but in a polymer frame striker-fired pistol. The Forward Set Trigger body is machined from aircraft-grade aluminum and black hard anodized to last a lifetime. The smooth-faced trigger comes assembled with a center pivoting safety. The Forward Set Sear & Trigger Kit boasts a smooth trigger pull throughout the break. The kit comes with two (2) trigger return springs; one designed to produce approximately a 4.0 lbs trigger pull (silver spring), and one to produce a 5.0 lbs trigger pull (green spring). These two options give the end-user the ability to customize their trigger pull for their specific needs.

The Apex M&P Competition Action Enhancement Kit was designed for the action shooting sports competitor. This drop-in kit will reduce trigger weight by approximately 4.0 lbs. (based on a starting trigger pull weight of 7.0 to 8.0 lbs.). The competition striker spring and trigger return spring are shot-peened to extend service life. The kit is engineered to be drop-in and should not require further gunsmithing (however, armorer or gunsmith installation is recommended). The M&P Competition Action Enhancement Kit is perfect for use with the M&P already equipped with the Apex Polymer or Aluminum Action Enhancement Trigger.

This kit is a combination of the Apex Duty/Carry Kit for the M&P Shield 45 and Shield 45 M2.0 and the Apex Action Enhancement Trigger for the M&P Shield 45 and Shield 45 M2.0. The Trigger Kit directly replaces the factory hinged trigger with a solid aluminum trigger body which reduces pre-travel and over-travel by approximately 20%. It features a smooth face with a center-mounted pivoting safety that maintains factory safety values. The Apex Duty/Carry Kit for the Shield 45 and Shield 45 M2.0 was designed to provide the pistol owner a smooth, consistent trigger pull that is approximately in the range of 5.0 to 5.5 lbs. with the advantages of shorter over-travel and more detectable trigger reset.

The Action Enhancement Kit features the Apex Action Enhancement Trigger with trigger bar and an Apex Performance Connector.

The Action Enhancement Kit features the Apex Action Enhancement Trigger with trigger bar and an Apex Performance Connector.

The Action Enhancement Kit features the Apex Action Enhancement Trigger with trigger bar and an Apex Performance Connector.

The Apex SD Polymer Action Enhancement Trigger directly replaces the factory hinged trigger with a solid body polymer trigger with a center-mounted pivoting safety. The rounded face of the trigger provides a smooth comfortable surface for the shooter’s finger. The trigger also reduces pre-travel by approximately 20% and over-travel by 10% when compared to the factory trigger and is perfect for use in SD and Sigma pistols already equipped with an Apex SD or Sigma Spring Kit. The trigger also works as a standalone component.

The Apex CZ P-10 Enhanced Slide Release offers wider, more ergonomic thumb paddles for easier manipulation of the slide release.

The Apex Extended Slide Release for the CZ P-10 offers wider, more ergonomic thumb paddles that are also extended toward the rear for easier manipulation of the slide release.

The Apex Extended Mag Release for the CZ P10c pistol is a direct replacement for the factory magazine release and improves performance by making it easier to release even a fully loaded magazine. Machined from bar-stock steel, fully heat-treated and finished in black Melonite, each features a 30 lines per inch checkered face. Tactical length is +0.080″ longer than the factory release.

The Apex Action Enhancement Kit for the CZ 75 B series pistols is designed to improve performance and reduce the large difference in trigger pull weight that exists between the double-action first shot and the subsequent single-action shots to approximately 2 pounds. The hammer and sear have matching Apex engineered single-action engagement surfaces that yield a clean, consistent single-action style trigger break while providing a smooth stack-free double-action. The matched sear and hammer engagement surfaces require eliminate the need for any polishing or stoning. *Note: for thumb safety models only. Includes Apex Performance Hammer for CZ 75 B (thumb safety models), Performance Matched Sear for CZ 75 B (thumb safety models), Duty/Carry Mainspring, Competition Mainspring, Reduced Power Firing Pin Spring and a set of two Replacement Hammer Pins.

The Apex Action Enhancement Kit for the FNS and FNS Longslide model pistols (2014 manufacture and later) is a direct drop-in replacement of the factory polymer trigger, trigger bar, and sear. The patent-pending Apex design reduces trigger pull weight to give you an approx. pull weight in the 5.5 lbs range. Overall trigger travel is optimized to provide a smooth uptake while delivering a crisp trigger break.

The Apex Action Enhancement Kit for Gen-5 Glock pistols delivers a smoother trigger pull with reduced travel, reset, and overall weight while maintaining factory safety standards. The red anodized aluminum trigger bar and performance connector provide approximately 1 pound of pull reduction and a crisp break point. As a direct drop-in replacement, it requires no gunsmithing and is compatible with G17, G19, G19x, G26, G34, and G45 Gen-5 models.

Specs

• Fit: Glock G17, G19, G19x, G26, G34, G45 Gen-5
• Color: Red anodized
• Includes: Trigger bar and connector
• Pull Weight Reduction: Approximately 1 pound
• Features: Smooth uptake, reduced reset/travel
• Installation: Drop-in, no gunsmithing
• Safety: Factory-standard center pivot
• Model: 102-156

Questions about fitment or availability? Give the shop a call and we’ll walk you through it.

Apex’s drop-in spring kit reduces J-Frame trigger pull by approximately 3 pounds while maintaining factory safety margins. Direct replacement parts make installation simple on all modern centerfire J-Frames.

Specs

• Model Number: 103-106
• Trigger Pull Reduction: ~3 lbs
• Installation: Direct drop-in
• Components: Rebound slide spring, main spring, firing pin, FP return spring
• Compatibility: All modern centerfire S&W J-Frames except Bodyguard .38
• Safety Maintained: Yes, factory safety specs
• Material: Hardened steel
• Compatibility Note: Requires removable frame-mounted firing pin

Questions about fitment or availability? Give the shop a call and we’ll walk you through it.

Apex Tactical’s patented Forward Set Sear kit transforms the M&P trigger with roughly 50% less travel, allowing shooters to position their finger lower on the trigger face for increased leverage. The smooth, consistent pull mimics single-action fire while maintaining full reliability in Gen 1 and earlier M&P models.

Specs

• Compatibility: S&W M&P 9, 40 (NOT M2.0, Shield, or .22)
• Type: Drop-in trigger kit
• Design: Flat-faced forward set sear
• Pull Weight: 3-5 pounds (varies by spring set)
• Travel Reduction: Approximately 50% less pre-travel and over-travel
• Reset: Shortened
• Finish: Black
• Feature: Patented reduced reset and travel

Questions about fitment or availability? Give the shop a call and we’ll walk you through it.

Apex’s steel optic mount allows secure mounting of Aimpoint ACRO or Steiner MPS sights to any Glock MOS platform via the factory 1913 interface. Machined from billet steel with black oxide finish, it requires only a 15 in-lb torque spec and ships with all necessary hardware.

Specs

• Fits: Glock MOS (Gen 4 & 5 models)
• Compatible Optics: Aimpoint ACRO P-1/P-2, Steiner MPS, Lead & Steel Pandora PB-3
• Material: Billet steel
• Finish: Black oxide
• Interface: 1913 Picatinny
• Made In: Arizona, USA

Questions about fitment or availability? Give the shop a call and we’ll walk you through it.

FEATURES:
-Reduces trigger pull by 1lb for duty/carry applications
-Requires Larger 1/8″ sear plunger & spring
-Fits M2.0 9mm/40S&W & M&P 45
-Polymer trigger

FEATURES:
-Reduces trigger pull by 2lbs
-Smooth uptake & reset
-Reduces reset length
-Reduces over-travel for duty/carry applications
-Fits M&P Shield 9mm/.40S&W

FEATURES
–Reduces pre-travel
-Reduces over-travel
-Reduces trigger pull
-Center mounted pivoting safety maintains factory safety values
-Fits Smith & Wesson M&P Shield 2.0 Pistols in 9mm & .40 Calibers