YOU MUST BE 18 OR OLDER TO ENTER

A/T Optic Riser 525-10×5 is approximately 6-1/8 long and offers a cantilever section for applications where the end user desires to run an attachment or optic over the handguard while avoiding bridging the optic from the upper to the handguard. This riser has 10 recoil slots on the main body, and 5 on the cantilever section for a total of 15 slots (16 lugs). Ideal for layering magnifiers and other enhancement systems with red dot optics, BCM A/T Risers offer the potential for a more capable platform that can improve threat identification in complex settings. Optimized for close combat ranges, the BCM A/T Riser creates a platform that raises the centerline of attached optics and magnifiers by approximately 1/2 inch. This additional height enhances the trained end users situational awareness, and further, makes it possible for them to take better aimed shots if they are using the optic in conjunction with night vision or other PPE systems. Interfacing with the upper receiver using the same low-profile A/T system used in our Optic Mounts, not only reduces snag hazards but makes the entire length of rail usable for either bolt-on or QD attachments. Further, the low profile A/T interface enables mounting accessories with Mil-Std 1913 attachments anywhere on the stalk of the riser platform allowing end users to fine tune placement of optics, magnifiers, and other accessories. Each A/T Riser is machined from aircraft aluminum alloy, hard coat anodized per Mil-A-8625F. The steel alloy clamp is hardened with Nitride coating for maximum strength. Finally, each Riser features multiple integral recoil lugs to mitigate recoil and counter recoil to preserve your zero and ensure no fail shots are placed where intended by the trained rifleman. A/T (Angled Torque) mounts employ angled torque through a patented* clamp which applies triangulating force to create a stronger and more reliable lock up of the mount onto the end users rail.

A/T Optic Riser 525-11 is approximately 4-1/2 long and is intended to be used with an optic backed up by a magnifier or NVG or thermal depending on the number of recoil slots the mount takes up. This riser has 11 recoil slots (12 lugs). Ideal for layering magnifiers and other enhancement systems with red dot optics, BCM A/T Risers offer the potential for a more capable platform that can improve threat identification in complex settings. Optimized for close combat ranges, the BCM A/T Riser creates a platform that raises the centerline of attached optics and magnifiers by approximately 1/2 inch. This additional height enhances the trained end users situational awareness, and further, makes it possible for them to take better aimed shots if they are using the optic in conjunction with night vision or other PPE systems. Interfacing with the upper receiver using the same low-profile A/T system used in our Optic Mounts, not only reduces snag hazards but makes the entire length of rail usable for either bolt-on or QD attachments. Further, the low profile A/T interface enables mounting accessories with Mil-Std 1913 attachments anywhere on the stalk of the riser platform allowing end users to fine tune placement of optics, magnifiers, and other accessories. Each A/T Riser is machined from aircraft aluminum alloy, hard coat anodized per Mil-A-8625F. The steel alloy clamp is hardened with Nitride coating for maximum strength. Finally, each Riser features multiple integral recoil lugs to mitigate recoil and counter recoil to preserve your zero and ensure no fail shots are placed where intended by the trained rifleman. A/T (Angled Torque) mounts employ angled torque through a patented* clamp which applies triangulating force to create a stronger and more reliable lock up of the mount onto the end users rail.

A/T Optic Riser 525-13 is approximately 5-3/4 long and covers the entire length of an upper receiver and offers one more recoil slot than the upper. This riser has 13 recoil slots (14 lugs). It can be used with any combination of sights, NVG, or thermal which would fit on an upper receiver and the additional slot gives the user some spacing flexibility. Ideal for layering magnifiers and other enhancement systems with red dot optics, BCM A/T Risers offer the potential for a more capable platform that can improve threat identification in complex settings. Optimized for close combat ranges, the BCM A/T Riser creates a platform that raises the centerline of attached optics and magnifiers by approximately 1/2 inch. This additional height enhances the trained end users situational awareness, and further, makes it possible for them to take better aimed shots if they are using the optic in conjunction with night vision or other PPE systems. Interfacing with the upper receiver using the same low-profile A/T system used in our Optic Mounts, not only reduces snag hazards but makes the entire length of rail usable for either bolt-on or QD attachments. Further, the low profile A/T interface enables mounting accessories with Mil-Std 1913 attachments anywhere on the stalk of the riser platform allowing end users to fine tune placement of optics, magnifiers, and other accessories. Each A/T Riser is machined from aircraft aluminum alloy, hard coat anodized per Mil-A-8625F. The steel alloy clamp is hardened with Nitride coating for maximum strength. Finally, each Riser features multiple integral recoil lugs to mitigate recoil and counter recoil to preserve your zero and ensure no fail shots are placed where intended by the trained rifleman. A/T (Angled Torque) mounts employ angled torque through a patented* clamp which applies triangulating force to create a stronger and more reliable lock up of the mount onto the end users rail.

The A/T Optic Riser 525-13×5 is approximately 7-1/4 long and is intended to be used similarly to the 525-10×5 but offers 3 additional recoil slots for more flexibility. This riser has 13 recoil slots on the main body, and 5 on the cantilever section for a total of 18 slots (19 lugs). Ideal for layering magnifiers and other enhancement systems with red dot optics, BCM A/T Risers offer the potential for a more capable platform that can improve threat identification in complex settings. Optimized for close combat ranges, the BCM A/T Riser creates a platform that raises the centerline of attached optics and magnifiers by approximately 1/2 inch. This additional height enhances the trained end users situational awareness, and further, makes it possible for them to take better aimed shots if they are using the optic in conjunction with night vision or other PPE systems. Interfacing with the upper receiver using the same low-profile A/T system used in our Optic Mounts, not only reduces snag hazards but makes the entire length of rail usable for either bolt-on or QD attachments. Further, the low profile A/T interface enables mounting accessories with Mil-Std 1913 attachments anywhere on the stalk of the riser platform allowing end users to fine tune placement of optics, magnifiers, and other accessories. Each A/T Riser is machined from aircraft aluminum alloy, hard coat anodized per Mil-A-8625F. The steel alloy clamp is hardened with Nitride coating for maximum strength. Finally, each Riser features multiple integral recoil lugs to mitigate recoil and counter recoil to preserve your zero and ensure no fail shots are placed where intended by the trained rifleman. A/T (Angled Torque) mounts employ angled torque through a patented* clamp which applies triangulating force to create a stronger and more reliable lock up of the mount onto the end users rail.

A/T Optic Riser 525-5 is approximately 2-1/8 long and is intended to be used with a red dot or other single optic or accessory. This riser has 5 recoil slots (6 lugs). All of our risers are the same 0.525 of rise over the top surface of the upper receiver. Ideal for layering magnifiers and other enhancement systems with red dot optics, BCM A/T Risers offer the potential for a more capable platform that can improve threat identification in complex settings. Optimized for close combat ranges, the BCM A/T Riser creates a platform that raises the centerline of attached optics and magnifiers by approximately 1/2 inch. This additional height enhances the trained end users situational awareness, and further, makes it possible for them to take better aimed shots if they are using the optic in conjunction with night vision or other PPE systems. Interfacing with the upper receiver using the same low-profile A/T system used in our Optic Mounts, not only reduces snag hazards but makes the entire length of rail usable for either bolt-on or QD attachments. Further, the low profile A/T interface enables mounting accessories with Mil-Std 1913 attachments anywhere on the stalk of the riser platform allowing end users to fine tune placement of optics, magnifiers, and other accessories. Each A/T Riser is machined from aircraft aluminum alloy, hard coat anodized per Mil-A-8625F. The steel alloy clamp is hardened with Nitride coating for maximum strength. Finally, each Riser features multiple integral recoil lugs to mitigate recoil and counter recoil to preserve your zero and ensure no fail shots are placed where intended by the trained rifleman. A/T (Angled Torque) mounts employ angled torque through a patented* clamp which applies triangulating force to create a stronger and more reliable lock up of the mount onto the end users rail.

FEATURES
-Pistol Grip
-Mod 0
-Black
-Reduced angle for improved ergonomics
-Hinged trap door offering storage inside the grip with a water resistant rubber gasket
-Each grip includes both an extended modular insert to close the gap between the trigger guard and pistol grip, and a smooth modular insert for use with some rifles with larger built in trigger guards. (User can decide which one to install)
-Made in the USA and manufactured from high quality impact resistant polymers.
-Test fit to ensure proper function (may display attributes consistent with this QC process)

FEATURES
-Pistol Grip
-Mod 0
-Flat Dark Earth
-Reduced angle for improved ergonomics
-Hinged trap door offering storage inside the grip with a water resistant rubber gasket
-Each grip includes both an extended modular insert to close the gap between the trigger guard and pistol grip, and a smooth modular insert for use with some rifles with larger built in trigger guards. (User can decide which one to install)
-Made in the USA and manufactured from high quality impact resistant polymers.
-Test fit to ensure proper function (may display attributes consistent with this QC process)

FEATURES
-Pistol Grip
-Mod 1
-Black
-Reduced angle for improved ergonomics
-Hinged trap door offering storage inside the grip with a water resistant rubber gasket
-Each grip includes both an extended modular insert to close the gap between the trigger guard and pistol grip, and a smooth modular insert for use with some rifles with larger built in trigger guards. (User can decide which one to install)
-Made in the USA and manufactured from high quality impact resistant polymers.
-Test fit to ensure proper function (may display attributes consistent with this QC process)

FEATURES
-Pistol Grip
-Mod 3
-Black
–Reduced angle for improved ergonomics and trigger control
-Hinged trap door offering storage inside the grip with a water resistant rubber gasket
-Each grip features an extended forward tang to close the gap between the trigger guard and pistol grip, and a high rise “beavertail” style back strap
-Up to a quarter of an inch wider than the BCMGUNFIGHTER Mod 0 and Mod 1 grips
-Made in the USA and manufactured from high quality impact resistant polymers
-Each grip test fit to ensure proper function (may display attributes consistent with this QC process)

FEATURES
-Pistol Grip
-Mod 3
-Flat Dark Earth
–Reduced angle for improved ergonomics and trigger control
-Hinged trap door offering storage inside the grip with a water resistant rubber gasket
-Each grip features an extended forward tang to close the gap between the trigger guard and pistol grip, and a high rise “beavertail” style back strap
-Up to a quarter of an inch wider than the BCMGUNFIGHTER Mod 0 and Mod 1 grips
-Made in the USA and manufactured from high quality impact resistant polymers
-Each grip test fit to ensure proper function (may display attributes consistent with this QC process)

FEATURES
-Pistol Receiver Extension Kit
-Buffer Tube
-For AR15 Pistols
–For your AR15, M16, M4 Pistol Lower Receiver. Pistol Receiver extension (buffer tube) machined from 7075T6
-Hard Coat Anodized per Mil-A-8625F, Type III, Class 2
-1.2″ outside diameter. Will fit your ATF compliant SigTac SB15 type pistol stabilizing brace. Works with carbine buffer and action springs.

FEATURES
–Fits standard 1913 Picatinny rail interface
-Accepts standard QD push button sling swivels
-Non-rotational locking interface
-Requires two lugs & one 1913 slot to mount properly
-All steel construction
-Includes hex wrench

FEATURES
-KMR Alpha
-13″
-Black
-KeyMod Free Float Handguard
-100% aluminum
-Lightweight and durable. Also featuring a proprietary patent pending mounting, indexing and lock up system that mitigates 12:00 rail movement under heat generated from the barrel nut.
-Handguard alone weighs 7.8 oz
-1.3″ Inner Diameter
-1.5″ OUTSIDE flat to flat
-Handguard flares forward (towards muzzle end) at the 3 and 9 O’Clock positions approximately 1/4″
-Actual length when measured to flare is 13.4″
-The KMR barrel nut will fit over all mil-spec diameter barrels (max of 1″)
-Mounting hardware, 2.4 oz, for a total of 10.2 oz on a very long 13″ rail
-The KMR Alpha is hardcoat anodized for corrosion resistance as well as to maintain a non-reflective finish.
-Includes BCM KeyMod Sling Mount

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS