YOU MUST BE 18 OR OLDER TO ENTER

YHM’s new line of sRx products were designed with aesthetics and ease-of-use as the top priorities and that is no different for the YHM sRx Short Flash Hider (YHM-4445's). This Q.D Flash Hider comes in three variations (5/8" x 24 5/8" x 32 & 11/16" x 24") and it's compatible Q.D. Adapter/Mounting Interface attaches to the industry standard (HUB) 1-3/8” x 24 threads. It features an internal taper seal-in front of the threads-that locks your suppressor on and forms a tight seal to contain gasses while in-use. This means no gasses or debris can build up on the threads.

The sRx Short Flash Hider must be paired with The YHM sRx Adapter (YHM-4400) .

The sRx Short Flash Hider adds minimal length and weight to the suppressor set up while also allowing you to reap all the benefits of the new YHM sRx System-when used in conjunction with The sRx Adapter. The full YHM sRx (Suppressor Rx) System will be the obvious choice for someone looking for a sleek low-profile suppressor set up-that’s also built to withstand rigorous use. This is our prescription for the shooter who cares about the aesthetics of their build as well as its ease-of-use.

Muzzle device length is 1.8". Length added to barrel is 1.175" (on barrels with 0.6" threads).

Some of the exciting new benefits of the YHM sRx System are as follows:

• TIMELESS. (No need to shim/time to barrel)
• Small/low profile
• No moving parts
• Large taper in front of the threads allows for consistent mounting.
• Lighter than many Q.D. mounting offerings on the market
• Can be permanently attached to firearm barrel needed
• Length: 1.8125"
• Diameter: .75"
• Material: 4140 Steel
• Finish: Black Phosphate
• Thread Size: sRx
• Caliber: .45 Caliber

The YHM sRx System-just what the doctor ordered!

YHM’s line of sRx products were designed with aesthetics and ease-of-use as the top priorities and that is no different for the YHM sRx Short Flash Hider (YHM-4445's). This Q.D Flash Hider comes in three variations (5/8" x 24 5/8" x 32 & 11/16" x 24") and it's compatible Q.D. Adapter/Mounting Interface attaches to the industry standard (HUB) 1-3/8” x 24 threads. It features an internal taper seal-in front of the threads-that locks your suppressor on and forms a tight seal to contain gasses while in-use. This means no gasses or debris can build up on the threads.

The sRx Short Flash Hider must be paired with The YHM sRx Adapter (YHM-4400) .

The sRx Short Flash Hider adds minimal length and weight to the suppressor set up while also allowing you to reap all the benefits of the new YHM sRx System-when used in conjunction with The sRx Adapter. The full YHM sRx (Suppressor Rx) System will be the obvious choice for someone looking for a sleek low-profile suppressor set up-that’s also built to withstand rigorous use. This is our prescription for the shooter who cares about the aesthetics of their build as well as its ease-of-use.

Muzzle device length is 1.8". Length added to barrel is 1.175" (on barrels with 0.6" threads).

Some of the exciting new benefits of the YHM sRx System are as follows:

• TIMELESS. (No need to shim/time to barrel)
• Small/low profile
• No moving parts
• Large taper in front of the threads allows for consistent mounting.
• Lighter than many Q.D. mounting offerings on the market
• Can be permanently attached to firearm barrel needed
• Length: 1.8125"
• Diameter: .75"
• Material: 4140 Steel
• Finish: Black Phosphate
• Thread Size: sRx
• Caliber: .45 Caliber
• Length: 1.8125"
• Diameter: .75"
• Material: 4140 Steel
• Finish: Black Phosphate
• Thread Size: sRx
• Caliber: .45 Caliber

The YHM sRx System-just what the doctor ordered!

YHM’s line of sRx products were designed with aesthetics and ease-of-use as the top priorities and that is no different for the YHM  sRx Short Flash Hider (YHM-4445's). This Q.D Flash Hider comes in three variations (5/8" x 24 5/8" x 32 & 11/16" x 24") and it's compatible Q.D. Adapter/Mounting Interface attaches to the industry standard (HUB) 1-3/8” x 24 threads. It features an internal taper seal-in front of the threads-that locks your suppressor on and forms a tight seal to contain gasses while in-use. This means no gasses or debris can build up on the threads.

The sRx Short Flash Hider must be paired with The YHM sRx Adapter (YHM-4400) .

The sRx Short Flash Hider adds minimal length and weight to the suppressor set up while also allowing you to reap all the benefits of the new YHM sRx System-when used in conjunction with The sRx Adapter. The full YHM sRx (Suppressor Rx) System will be the obvious choice for someone looking for a sleek low-profile suppressor set up-that’s also built to withstand rigorous use. This is our prescription for the shooter who cares about the aesthetics of their build as well as its ease-of-use.

Muzzle device length is 1.8". Length added to barrel is 1.175" (on barrels with 0.6" threads).

Some of the exciting new benefits of the YHM sRx System are as follows:

• TIMELESS. (No need to shim/time to barrel)
• Small/low profile
• No moving parts
• Large taper in front of the threads allows for consistent mounting.
• Lighter than many Q.D. mounting offerings on the market
• Can be permanently attached to firearm barrel needed
• Length: 1.8125"
• Diameter: .75"
• Material: 4140 Steel
• Finish: Black Phosphate
• Thread Size: sRx
• Caliber: .45 Caliber

The YHM sRx System-just what the doctor ordered!

YHM’s new line of sRx products were designed with aesthetics and ease-of-use as the top priorities and that is no different for the YHM sRx Short Muzzle Brake (YHM-4445-MB). This Q.D Muzzle Brake comes in three variations (5/8 x 24" 5/8 x 32" & 11/16" x 24) and it's compatible Q.D. Adapter/Mounting Interface attaches to the industry standard (HUB) 1-3/8” x 24 threads. It features an internal taper seal-in front of the threads-that locks your suppressor on and forms a tight seal to contain gasses while in-use. This means no gasses or debris can build up on the threads.

The sRx Short Muzzle Brake must be paired with The YHM sRx Adapter (YHM-4400) .

The sRx Short Muzzle Brake adds minimal length and weight to the suppressor set up while also allowing you to reap all the benefits of the new YHM sRx System-when used in conjunction with The sRx Adapter. The full YHM sRx (Suppressor Rx) System will be the obvious choice for someone looking for a sleek low-profile suppressor set up-that’s also built to withstand rigorous use. This is our prescription for the shooter who cares about the aesthetics of their build as well as its ease-of-use.

Muzzle device length is 2.3". Length added to barrel is 1.675" (on barrels with 0.6" threads).

Some of the exciting new benefits of the YHM sRx System are as follows:

• TIMELESS. (No need to shim/time to barrel)
• Small/low profile
• No moving parts
• Large taper in front of the threads allows for consistent mounting.
• Lighter than many Q.D. mounting offerings on the market
• Can be permanently attached to firearm barrel needed
• Length: 1.6875"
• Diameter: .75"
• Material: 4140 Steel
• Finish: Black Phosphate
• YHM-4445-MB-24 5/8" – 24: .45 Caliber
• Thread Size: sRx

The YHM sRx System-just what the doctor ordered!

YHM’s line of sRx products were designed with aesthetics and ease-of-use as the top priorities and that is no different for the YHM sRx Short Muzzle Brake (YHM-4445-MB). This Q.D Muzzle Brake comes in three variations (5/8 x 24" 5/8 x 32" & 11/16" x 24) and it's compatible Q.D. Adapter/Mounting Interface attaches to the industry standard (HUB) 1-3/8” x 24 threads. It features an internal taper seal-in front of the threads-that locks your suppressor on and forms a tight seal to contain gasses while in-use. This means no gasses or debris can build up on the threads.

The sRx Short Muzzle Brake must be paired with The YHM sRx Adapter (YHM-4400) .

The sRx Short Muzzle Brake adds minimal length and weight to the suppressor set up while also allowing you to reap all the benefits of the new YHM sRx System-when used in conjunction with The sRx Adapter. The full YHM sRx (Suppressor Rx) System will be the obvious choice for someone looking for a sleek low-profile suppressor set up-that’s also built to withstand rigorous use. This is our prescription for the shooter who cares about the aesthetics of their build as well as its ease-of-use.

Muzzle device length is 2.3". Length added to barrel is 1.675" (on barrels with 0.6" threads).

Some of the exciting new benefits of the YHM sRx System are as follows:

• TIMELESS. (No need to shim/time to barrel)
• Small/low profile
• No moving parts
• Large taper in front of the threads allows for consistent mounting.
• Lighter than many Q.D. mounting offerings on the market
• Can be permanently attached to firearm barrel needed
• Length: 1.6875"
• Diameter: .75"
• Material: 4140 Steel
• Finish: Black Phosphate
• YHM-4445-MB-24 5/8" – 24: .45 Caliber
• Thread Size: sRx

The YHM sRx System-just what the doctor ordered!

YHM’s new line of sRx products were designed with aesthetics and ease-of-use as the top priorities and that is no different for the YHM sRx Short Muzzle Brake (YHM-4445-MB). This Q.D Muzzle Brake comes in three variations (5/8 x 24" 5/8 x 32" & 11/16" x 24) and it's compatible Q.D. Adapter/Mounting Interface attaches to the industry standard (HUB) 1-3/8” x 24 threads. It features an internal taper seal-in front of the threads-that locks your suppressor on and forms a tight seal to contain gasses while in-use. This means no gasses or debris can build up on the threads.

The sRx Short Muzzle Brake must be paired with The YHM sRx Adapter (YHM-4400) .

The sRx Short Muzzle Brake adds minimal length and weight to the suppressor set up while also allowing you to reap all the benefits of the new YHM sRx System-when used in conjunction with The sRx Adapter. The full YHM sRx (Suppressor Rx) System will be the obvious choice for someone looking for a sleek low-profile suppressor set up-that’s also built to withstand rigorous use. This is our prescription for the shooter who cares about the aesthetics of their build as well as its ease-of-use.

Muzzle device length is 2.3". Length added to barrel is 1.675" (on barrels with 0.6" threads).

Some of the exciting new benefits of the YHM sRx System are as follows:

• TIMELESS. (No need to shim/time to barrel)
• Small/low profile
• No moving parts
• Large taper in front of the threads allows for consistent mounting.
• Lighter than many Q.D. mounting offerings on the market
• Can be permanently attached to firearm barrel needed
• Length: 1.6875"
• Diameter: .75"
• Material: 4140 Steel
• Finish: Black Phosphate
• YHM-4445-MB-24 5/8" – 24: .45 Caliber
• Thread Size: sRx

The YHM sRx System-just what the doctor ordered!

YHM's sRx protective cap will keep the threads on your sRx mounts from becoming dirty or damaged when your suppressor is not in use.

• Weight: 0.448 Oz.
• Length: .5625"
• Diameter: 1"
• Material: 4140 chrome moly steel
• Finish: black oxide
• Designed to be used with the YHM sRx System & any suppressor with 1 3/8" thread.

FEATURES
-Made from 7075-T6 aluminum (forged)
-M4 style feed ramps & “T” markings
-Inside coated with dry film lube
-Accepts standard upper receiver parts (dust covers, forward assists, etc.)
-Accepts Mil-Spec lower receivers
-Fit & function with your standard lower receiver
-Hardcoat anodized matte black to Military Specifications or better

FEATURES
-Made from 7075-T6 aluminum (billet)
-M4 style feed ramps
-Inside coated with dry film lube
-Accepts standard upper receiver parts (dust covers, forward assists, etc.)
-Accepts Mil-Spec lower receivers
-Fit & function with your standard lower receiver
-Hardcoat anodized matte black to Military Specifications or better

YHM’s suppressor gas block is designed for customers looking for an affordable way to tune their AR for shooting suppressed. This gas block features a gas port hole that’s 50% smaller than a standard gas block. This reduced gas port decreases ,port pop, and mitigates blowback to the shooter, making shooting suppressed much more enjoyable. Due to variations in barrel gas port size, barrel length, caliber, suppressor design, ammunition, etc., this item may require the customer to fine-tune the port size to match their exact setup. It is designed to be used on a host firearm that will be shot exclusively with a suppressor attached.

The VICTRA-12 internal choke is a specialized choke that sits in the front of the suppressor not in the shotgun's barrel. The choke of a shotgun determines shot string only. It has no bearing on shot speed (velocity) or distance (range). That is the choke does not alter the shotgun's power—it just controls how tight or spread out the pellets will be at a specific distance.

The three different choke sizes are all made of 17-4 Stainless Steel and are all machined for our VICTRA-12 12ga modular shotgun suppressor.

• Made in the U.S.A.
• Length: 1.00"
• Diameter: 1.050"
• Material: 17-4 Stainless Steel
• Finish: Natural Stainless
• Caliber: 12ga

The VICTRA-12 Mount Assembly is a bit different than your ordinary mount assembly. Ours threads into the end of your shotgun's barrel using the standard choke threads to mount the suppressor to the shotgun but it does not choke your shot. That is handled by our unique front-installed choke. Each mount is shotgun-manufacturer specific and we offer a multitude of mounts that function with most popular shotguns.

MADE IN U.S.A.

REMINGTON MOUNT ASSEMBLY
Length: 2.980"
Diameter: 1.20"
Material: 17-4 Stainless Steel
Finish: Melonite

The VICTRA-12 Mount Assembly is a bit different than your ordinary mount assembly. Ours threads into the end of your shotgun's barrel using the standard choke threads to mount the suppressor to the shotgun but it does not choke your shot. That is handled by our unique front-installed choke. Each mount is shotgun-manufacturer specific and we offer a multitude of mounts that function with most popular shotguns.

MADE IN U.S.A.

REMINGTON MOUNT ASSEMBLY
Length: 2.980"
Diameter: 1.20"
Material: 17-4 Stainless Steel
Finish: Melonite

The VICTRA-12 internal choke is a specialized choke that sits inside the front of the suppressor. The choke of a shotgun determines shot shape and as such it is an important part of any shotgun. The Victra-12 places the choke at the end of the suppressor in the optimal place. YHM's five different choke sizes are all made of 17-4 Stainless Steel and are machined specifically for our VICTRA-12 12ga modular shotgun suppressor.

• Material: 17-4 Stainless Steel
• Finish: None
• Gauge: 12
• Made in the USA.

The VICTRA-12 Shotgun Suppressor is modular and one of the major pieces to that are our 5/32" Allen sleeve nuts that attach on our V-12 endcap and keep the assembly rods in place.

This set of replacement nuts are available for the chance that you either lose your sleeve nuts or want a second set to keep in your shotgun kit.

MADE IN U.S.A.

• Length: .5"
• Weight: 1 Oz.
• Material: Steel
• Finish: Hard Anodized

5/32" Allen wrench not included.

Designed to protect the threads of your VICTRA-12 mounting device when the suppressor is not in use. It is machined from 6061 T6 aluminum to very high quality standards. It has a durable hard coat anodized finish.

MADE IN U.S.A.

• Length: 3.320"
• Diameter: 1.2"
• Material: 6061 T6 Aluminum
• Finish: Hard Anodize

The VICTRA-12 internal choke is a specialized choke that sits inside the front of the suppressor. The choke of a shotgun determines shot shape and as such it is an important part of any shotgun. The Victra-12 places the choke at the end of the suppressor in the optimal place. YHM's five different choke sizes are all made of 17-4 Stainless Steel and are machined specifically for our VICTRA-12 12ga modular shotgun suppressor.

• Material: 17-4 Stainless Steel
• Finish: None
• Gauge: 12
• Made in the USA.

The VICTRA-20 Mount Assembly differs from other shotgun suppressor mounts. YHM's threads into the end of your shotgun's barrel using the standard choke threads to secure the suppressor to the shotgun but it does not provide any choke or constriction to the shot load. That job is handled by our unique choke cone which is located in the front cap of the V-20 suppressor itself. Each mount is shotgun-manufacturer specific and we offer a growing range of mounts that function with popular shotgun brands/models.

The YHM V-20 Jam Nut (YHM-1250) is included with every mount.

• Length Added to Barrel: .950”
• Material: 17-4
• Stainless Steel
• Finish: Melonite
• Gauge: 20
• Made in the USA